4G63 6bolt swap Questions

What was done to this engine?

• Head machined, pressure tested, and surfaced
• New intake and exhaust valves
• New revised lifters
• New MLS metal headgasket
• New ARP headbolts
• Block bored and honed
• New 1gen turbo pistons
• New 1gen turbo piston rings
• 1gen big rods
• Standard virgin polished crankshaft “never been cut”
• New rod bearings
• New main bearings
• Oil squirters eliminated
• Balance shafts eliminated
• New OEM oil pump
• New OEM timing belt idler bearings
• New OEM hydraulic timing belt tensioner
• New water pump
• New timing belt

What does this engine include with it?

• 1gen thermostat housing
• 1gen upper water neck
• 1gen water pump pipe
• 2gen front cast iron bracket for engine mount
• 1gen big port intake manifold with 2gen map sensor provision
• 6bolt oil pan
• Oil filter adapter
• New intake gasket
• New exhaust gasket

What do I need to finish up my swap??

• 6bolt flywheel remember AWD and FWD are different when ordering
• New aftermarket external oil cooler “any auto parts should have in stock”
• Also cooler can be found in a 1989-90 talon eclipse turbo but we recommend a new one.

Do you have any installation tips for me?

• Always check all water and oil hoses and clamps, if they look suspicious it's a good thing to replace them.
• Note this engine will not come with any sensors so remember to use your crank and cam sensors look at pictures on the right for location of these sensors.
• Note this engine is built to fit years ranging 95-99. If your working on a 95-96 model you will to reuse your intake camshaft timing sprocket to work with your cam sensor located in front of engine cyl head. And if your working on a 97-99 model your cam sensor is located on the rear of intake camshaft. and all model 95-99 have the crank sensor on front of oil pump casing.
• When replacing these sensors you have to remove timing belt so please make sure you time your engine back properly a mistake here will ruin valves and you will need a valve job."Costly mistake"
• Oil filter adapter on our engine has three brass fitting one is a T fitting to accommodate both oil gauge and oil light sensors/sending unit the other two are for an external oil cooler thats where you hook it up also see pictures for a better understanding.
• Always when installing a turbo engine double check your turbo unit for any sloppiness on turbine shaft,because a bad turbo can be the cause of killing a good engine by sucking oil so please check your turbo unit make for sure it isn't using up oil. "good sign would be extreme smoke upon accelerations"
• If your car still has the factory plastic radiator please after installation check all seams for leaks these plastic radiators after time seem to have coolant seapage around tank seals.
• We also recommend a new radiator cap located on upper water neck."better to be safe then sorry"

What does this engine cost?

• This engine they way you see it is $2350.00 with core exchange .
• Core exchange means we will charge a core deposit of $250.00 on top of engine price, when we receive your core longblock back we will refund your core deposit. Engine is sold as pictured and will include everything mentioned all except for 6bolt flywheel and external oil cooler.

What kind of warranty do I get and what does it cover?

• The warranty on this engine is 6 months 6,000 miles
• Parts only NO labor or shipping warranty.
• This warranty covers everything except for OVERHEATING and ABUSE.
• If your the type of person looking to boost 18lbs or higher on a daily basis this is not the engine for you.
• If something was to fail within the warranty conditions and period time you as the consumer are liable for any labor and shipping cost.

What kind of payment do you except?

• We except all major credits cards (visa,mastercard,american express,discover)
• We except money orders and certified checks (merchandise will not be shipped until it clears though)
• We also except PAYPAL and CASH.
• Payment plans can be arranged by calling us for details... 1 800 843 8349.....George Martin

If I'm able to bring in my vehicle can you do the installation?

• Yes we can do the installation here at Kar King Auto we been servicing all local dealerships for the past 15 years and have 3 installers on the premises at all times.
• Price on the labor to remove your 7bolt 4G63 and replace it with our 6bolt 4G63 is $550.00
• Please also consider parts and california sales tax on engine and necessary parts
• We replace in necessary parts Oil,Oil filter,Spark plugs,Anti-freeze
• If you need a tow to get your car to us we recommend A and Y flatbed services
  1 951 377 6442 talk to adolfo he will hook it up.

Can you ship this engine?

• Yes we ship nationwide call us for pricing to your area.
• We also ship locally within 100 miles from us delivery charge of $45.00 will be applied.
• And everyone is more then welcomed to pick up merchandise on will call.
• No residential drop off on any freight truck delivery.

Do you have a recommended break in period?

• Yes please keep it under 65MPH for the first 500 miles after installation.
• Change oil at the first 1500 miles and every 3000 miles after that.
• Remember proper maintenance will always prolong your engines life.

The first 2gen 6bolt finished up longblock!

• Checkout the pictures of the final product.
• Also keep in mind this engine can be built with a 2gen cylinder head if you prefer that just let us know what you want either way it isn't a problem.